Pipe and Draping Straight Swag (7′ – 10′ Long Section)

$157.00 $119.00

✔  Your Date + Get a Quote Now
Event Date:

When draping a tent/pavilion perimeter, secure uprights to pillars halfway up. This reduces the wind knocking over your drapery. Secure uprights to pillars with tape, zip ties, or rope (not provided). Zip tie all overlapped fabric together to prevent the wind from separating it during the event. For tents use this or free-standing corners, not both.

Enter state/date to select quantity  📦 10 ft long kit includes zip ties, (2) uprights, (2) base plates, (1) crossbar, (4) pieces of drapery fabric, you may need more zip ties

–  Important: fabric can’t be cut, altered, dyed, or stained
–  Width Adjusts: 7 ft – 10 ft long
–  Height Adjusts: 4 ft – 10 ft tall
–  Setup Size: 10 ft long x 10 ft tall
–  Setup Time: 15 mins per 10-foot kit
–  Fabric Material: poly-silk
–  Default Fabric Color: white
–  Also Avail: purple, light purple, red, pink, ivory, teal, blue, black
–  Upgrades: reserve (2) outdoor uplights per kit to add colors
–  Flame Retardant Fabric: Yes
–  Wrinkle-Resistant Drapery: Yes
–  Weight & Dimensions: view in additional information tab below
–  Rentals Arrive: 2-days prior to the event date
–  Duration: Send back 2-day after event date to avoid late fees
–  FREE Nationwide Shipping both ways on orders over $94


Easy Do It Yourself Rentals (1 Min)

Learn how to set up this rental by watching the video below



Read: The Top 7 Wedding Draping Kits

How to Measure
: Multiply the number of people sitting in front of the draping then round up to the next 10. If you have 12 people x 2-foot = 24, then round up to 30. You would need to reserve a 30-foot backdrop. Read more about draping measurements for a larger space. If you want to know how to decorate pipe and drape, then rent straight swagged pipe and drapery today. Read More...


(11) Important DIY Pipe & Draping Straight Swag Wedding Tips, Tricks & Pro Advice









Additional information

Weight 49 lbs
Dimensions 57 x 19 x 8 in


There are no reviews yet.

Be the first to review “Pipe and Draping Straight Swag (7′ – 10′ Long Section)”

Easy Setup Instructions

How to decorate pipe and drape with straight swag backdrop

  1. place crossbars end to end on the ground and center on the space you want to drape
  2. put base plates at the bottom edges of all the crossbars (make sure ferrule pin is screwed into center hole)
  3. slide uprights into the baseplates ferrule pin all the way (do not force upright down onto ferrule pin all the way if they don’t fit, only force down 50% if tight)
  4. attach crossbars between (2) uprights slots, make sure crossbar is in the slot all the way (do this for all crossbar sections)
  5. now that you have a fully completed skeleton, throw (4) pieces of fabric over each single crossbar (try to keep the same amount of fabric on both sides of a single crossbar when throwing it over) Tip if you are using silver sequin or gold sequin fabric then you will insert this crossbar into the pole pocket
  6. pleat fabric overlap fabric edges & cover any hardware, make sure the center of your crossbar is the center point of the 2 pieces of overlapped fabric)
  7. use a zip-tie or clip on the back of the 2 pieces in the center front row of fabric (repeat this for each 10 foot section) this holds together your fabric when you pull it back in steps 9-11
  8. raise uprights individually in 2 foot increments until entire backdrop is 10 foot high
  9. pull back 2 left pieces of fabric and gather towards left upright, adjust fullness by accordion pieces in hand, attach with zip-tie or pipe cleaner to left upright
  10. pull back 2 right pieces of fabric and gather towards right upright, adjust fullness by accordion pieces in hand, attach with zip-tie or pipe cleaner to right upright
  11. repeat steps 9 & 10 if you have more than 10 feet of draping
  12. finalize bottom by lifting each piece of fabric, accordion fabric down, and tuck and roll the bottoms

QR Code

Scan for Fast Access to this Product Page

You may also like